FREE TOOL

Free Garment Spec Sheet Generator

Build the measurement page a factory checks your samples against. Choose a garment, type the measurements from a piece that fits the way you want, set how much each size steps up or down, and the full size run fills itself in. Export it as a spreadsheet or a PDF. It all runs in your browser: no account, nothing uploaded.

Build your spec sheet

Add your brand and style details at the top, pick the garment and the unit, then set the sample size and the smallest and largest sizes you will sell. Every row is editable, and you can add rows for anything special on your design.

Edit the base, grade and tolerance for each point. The size columns update as you type. Starting values are examples for a size M sample, not a standard: replace them with measurements from your own fit sample.

Point of measureBase (M)GradeTol +/-XSSMLXL2XLRemove
272829303132
192021222324
192021222324
16.517.251818.7519.520.25
7.588.599.510
6.7577.257.57.758
88.599.51010.5
6.7577.257.57.758
3.53.6253.753.87544.125
0.750.750.750.750.750.75
0.750.750.750.750.750.75
111111

What goes on a garment spec sheet

A spec sheet (also called a measurement chart or size spec) is the table of numbers behind one style. Each row is a point of measure, a written note on exactly where the tape goes, the allowed tolerance, and the value for every size you produce.

It is the page your sample maker cuts the pattern from and the page your quality checker holds next to the finished piece. If the numbers are vague, two factories will give you two different garments from the same sketch.

Measuring a garment you already like

The quickest way to get good starting numbers is to measure a piece from your own wardrobe or a competitor brand that already fits the way you want. Lay it flat on a table, smooth it without stretching, and measure each point the way the "how to measure" note says.

  • Width points marked "half" are taken across one layer, from side seam to side seam.
  • Lengths start at the high point shoulder (HPS): the spot where the shoulder seam meets the collar.
  • Measure knits relaxed. Pulling rib or jersey adds up to an inch.
  • Measure the same point twice. If the two readings differ, use the smaller one and check again.

Size grading in plain words

Grading is the step between one size and the next. Your sample size keeps the numbers you measured, and each size above it adds the grade once per step, while each size below takes it away. The table in the tool does that maths for you as you type.

PointTypical grade (tee)Why
Chest, hem width (half)1 in / 2.5 cmBodies get wider fastest between sizes.
Body length1 in / 2.5 cmTaller people buy bigger sizes.
Shoulder3/4 in / 2 cmGrows a bit slower than the chest.
Sleeve length, neck width1/4 to 1/2 inSmall changes keep the look the same.
Rib and hem height0Trims stay the same size across the run.

These are common starting values, not a rule. Plus-size runs often need a bigger grade above XL, so change the grade for any point that needs it.

Picking tolerances your factory can hit

Tolerance is the plus or minus you will accept before a piece fails. Too tight and good garments get rejected; too loose and a large can measure like a medium. A simple check: keep every tolerance at or below half of that point’s grade, so neighbouring sizes never overlap.

After the first sample arrives

  • Measure the sample at every point on the sheet and write the real value next to the spec.
  • Mark anything outside tolerance and send that list back with the sheet.
  • Try it on a person, not only flat. Fit issues like a tight armhole show up on the body first.
  • Update the sheet so the next round and bulk production use the corrected numbers.
  • Once it is approved, shoot it: a product photo on a model sells the piece long before stock arrives.

FAQ

Is a spec sheet the same as a tech pack?

No. The spec sheet is the measurement table. A tech pack is the whole instruction pack for a style: sketches, fabrics and trims, construction, labels and the spec sheet as one part. Our tech pack generator writes the rest.

Do I need a spec sheet for print on demand?

Usually not. Print-on-demand partners use their own blank garments with their own size charts. You need one when a factory or sample maker cuts and sews a design for you.

Inches or centimeters?

Use whatever your factory works in. Many factories in Asia work in centimeters, many US sample makers in inches. The tool converts every value when you switch.

Where do the starting numbers come from?

They are typical example values for a size M sample, there so the table is not empty. Replace them with measurements from your own fit sample before you send anything.

Can I add my own measurement points?

Yes. Press "Add point of measure", type the name and the how-to-measure note, and set the base, grade and tolerance. Remove any row you do not need.

Does the tool save my sheet?

No. Nothing leaves your browser. Download the CSV or save the PDF before you close or refresh the page.

More free tools for clothing brands

Start your clothing brand

From the first idea to production: plan the line, write the slogan, build the tech pack and spec sheet, and cost every piece.

How to Start a Clothing Brand

More for clothing sellers